科研 Skill

热流体设计计算

thermal-fluids-calc

Computes pipe/duct pressure drop, pump head, heat exchanger rating and sizing (LMTD/e-NTU), fin design, and fluid properties via CoolProp. Use for thermal-fluids sizing calculations with SI inputs.

发布者 Codar安全审核通过v0.1.0更新于 2026-11-18

SKILL.md

Thermal-Fluids Calculator

Run scripts/thermo_fluids.py (needs pip install CoolProp). Inputs are in SI. Convert first and state the conversion.

Workflow

  1. Classify: internal flow, heat exchanger, extended surface, or properties only.
  2. Get properties at the right temperature: use the mean bulk temperature for heat exchangers. Always use props; never use remembered property values.
    python scripts/thermo_fluids.py props --fluid Water --T 40
    
    CoolProp names: Water, Air, R134a, R1234yf, Nitrogen, CO2, INCOMP::MEG-30% (glycol mix).
  3. Calculate
    # Pressure drop in 50 m of 2" sch40 steel pipe, 4 L/s water, 3 elbows + valve
    python scripts/thermo_fluids.py pipe --D 0.0525 --L 50 --Q 0.004 --K 3.2 --T 20
    # Rate an exchanger with known UA
    python scripts/thermo_fluids.py hx --mh 0.5 --cph 4180 --mc 0.8 --cpc 4180 --Thi 80 --Tci 15 --UA 2500
    # Size for a duty, report area for U = 800 W/m2K
    python scripts/thermo_fluids.py hx --mh 0.5 --cph 4180 --mc 0.8 --cpc 4180 --Thi 80 --Tci 15 --q 60000 --U 800
    # Aluminum fin
    python scripts/thermo_fluids.py fin --k 200 --h 40 --L 0.03 --t 0.002 --w 0.05 --Tb 85 --Tinf 25
    
    Typical minor-loss K values and U ranges are in references/coefficients.md.
  4. Check: energy balance closes (q = Ch·ΔTh = Cc·ΔTc), no temperature cross, Re regime stated, velocities reasonable.
  5. Report: assumptions → results table → checks → recommendation (pipe size, exchanger area with a 10–25% fouling margin, fin count).

示例提示词

帮我用LMTD法计算这台换热器所需的换热面积。

所属插件

机械设计与先进制造面向机械设计与制造研究:文本/草图生成 CAD、FreeCAD/SolidWorks 参数化建模、机构综合与零件选型、公差与 GD&T、DFM 与设计评审、快速有限元与应力代理模型、增材制造工艺与缺陷预测、疲劳断裂寿命。

安装该插件会一并获得同领域的 35 个 Skill / MCP。

同插件的其他科研 Skill

常见问题

热流体设计计算能做什么?

Computes pipe/duct pressure drop, pump head, heat exchanger rating and sizing (LMTD/e-NTU), fin design, and fluid properties via CoolProp. Use for thermal-fluids sizing calculations with SI inputs。

如何安装热流体设计计算?

在科搭 Codar 左侧点击「插件」,在「组件」页签搜索「热流体设计计算」并安装;在 Claude Code 或 Codex 中可以发送本页的安装提示词,或下载 Skill 包后解压到 ~/.claude/skills 或 ~/.codex/skills。

热流体设计计算需要哪些权限?

该科研 Skill没有声明额外权限;执行具体操作时仍由 Agent 按自身规则请求确认。

热流体设计计算经过官方审核吗?

是。SpeedSkills 收录的每个版本都会记录内容摘要与权限声明,当前版本已通过安全审核。