科研 Skill
继电保护级差整定
protection-coordination-study
Checks relay/breaker/fuse time-current coordination and selectivity margins from short-circuit results. Use when sizing protective devices or diagnosing a miscoordination.
SKILL.md
Protection Coordination Study
Determines whether a power system's protective devices (relays, circuit breakers, fuses) will isolate a fault with the correct device, in the correct order, without unnecessarily tripping healthy equipment upstream. This is a distinct engineering discipline from the steady-state and dynamic studies the rest of this plugin covers (power flow, stability, hosting capacity): those tell you the system is healthy in normal and contingency operation; this skill tells you it will fail safely and selectively when something actually breaks.
When to use this
- Sizing or specifying breakers, relays, or fuses for a new feeder, substation, or interconnection.
- A time-current coordination study shows overlapping curves, a miscoordination (the wrong device trips first), or no margin between an upstream and downstream device.
- Investigating a nuisance trip (a breaker opened for a fault that a downstream device should have cleared) or a failure to trip (a fault persisted because no device operated).
- Following up a
short-circuit-mitigationfinding that breaker interrupting duty is close to its rating, or aninterconnection-impact-mitigationfinding that a new source changes fault current seen by existing relays.
This skill assumes a short-circuit study has already produced fault-current
magnitudes at each bus (from surge, pandapower, psse, pslf,
powerworld, or a hand calculation); it does not replace that calculation,
it consumes its output.
Core concepts
- Protective device types and their curves.
- Fuses: a fixed, non-adjustable time-current characteristic (TCC) from the manufacturer, published as minimum-melt and total-clearing curves.
- Thermal-magnetic/electronic trip breakers: TCC with adjustable pickup and, on electronic trips, adjustable long-time, short-time, and instantaneous settings.
- Protective relays (overcurrent 50/51, differential 87, distance 21, etc. in IEEE device-function numbers): programmable pickup, time dial, and curve shape (IEC or IEEE/ANSI standard inverse-time curves), driving a separate breaker.
- Standard inverse-time curve families (needed to reproduce a relay's
TCC numerically):
- IEC 60255: standard inverse, very inverse, extremely inverse —
t = TMS × (k / ((I/Ipickup)^α − 1))with (k, α) = (0.14, 0.02), (13.5, 1), (80, 2) respectively for the three curve types. - IEEE C37.112 (ANSI) curves: moderately/very/extremely inverse, with their own published (A, B, p) coefficient sets per curve. Always confirm the exact coefficients and the relay's actual implementation against its manual — vendors sometimes offer both IEC and IEEE curve tables in the same relay, selected by a setting.
- IEC 60255: standard inverse, very inverse, extremely inverse —
- Selectivity (discrimination) margin. The industry rule of thumb is a minimum 0.2–0.4 s time margin between an upstream device's curve and the downstream device's total-clearing curve, at the maximum fault current the downstream device will see, to allow for breaker operating-time tolerance and relay overshoot. Confirm the exact margin your utility or standard requires — it is a design choice, not a universal constant.
- Three zones of a well-coordinated study: (1) downstream device clears a fault on its own section without upstream operation, (2) if it fails, the next device upstream clears with acceptable additional outage, (3) no device at any level exceeds its interrupting rating for the maximum fault current it can see (this is the short-circuit duty check).
Procedure
-
Gather fault-current data per bus/zone. Pull maximum (bolted three-phase, for device duty) and minimum (often line-to-ground at the far end of a zone, for pickup sensitivity) fault current at every bus the study covers. Use the plugin's power-flow/short-circuit tools (
surge,pandapower,psse/pslfvia PowerMCP) or a dedicated ANSI/IEC short-circuit program (SKM, EasyPower, ETAP) for a production-grade number — these tools differ (ANSI vs. IEC short-circuit methods give different multiplying factors), so note which method was used. -
Build or import each device's TCC. For library devices,
scripts/tcc_plot.py --device references/tcc-library/<vendor>/<model>.jsonplots the curve from a stored (pickup, time-dial, curve-type) parameter set using the IEC/IEEE formulas above. For a non-library device, digitize the manufacturer's published TCC (most vendors publish them as PDF log-log plots; some publish the coefficient table directly — prefer that when available over digitizing a plot by eye). -
Overlay adjacent devices on one log-log plot.
scripts/coordination_plot.py --devices device_a.json device_b.json --fault-range <Imin> <Imax>draws every device in a protection chain on one current-vs-time axis and highlights the fault-current range the two devices must discriminate over (from step 1's minimum/maximum per zone). -
Check each coordination pair for:
- Selectivity: downstream curve's total-clearing time is below the upstream curve's minimum operating time by the margin from the Core Concepts section, across the whole fault-current range the pair can see.
- Sensitivity: every device picks up (its curve is defined and operates) at the minimum fault current its zone can produce — a pickup set too high will not sense a far-end or high-impedance fault.
- Speed: the fastest-clearing device consistent with selectivity is chosen for safety and equipment-damage reasons (e.g. arc-flash energy, which scales with clearing time); do not add margin beyond what selectivity requires.
- Device duty: the maximum fault current at that device's location
does not exceed its interrupting/withstand rating — pair with
short-circuit-mitigationif it does.scripts/tcc_plot.pyandscripts/coordination_plot.pyboth accept--reportto emit a numeric table of margins at a list of test currents instead of (or alongside) the plot, for a documented pass/fail record.
-
Check special cases explicitly, not just the normal radial chain:
- Inrush and cold-load pickup: a transformer or motor's energizing inrush current can exceed normal load by 6–12× for a few cycles; the protective device's pickup and short-time curve must ride through this without tripping (check against the device's "no trip" region, not just its minimum pickup).
- CT saturation: a current transformer feeding a relay can saturate at high fault current, distorting the relay's view of the fault — relevant for differential and high-set instantaneous elements; check the CT's accuracy class and knee-point voltage against the maximum fault current, not just its nameplate ratio.
- Bidirectional/multi-source fault paths (parallel feeders, DER,
ring buses): a device may need directional elements (relay function 67)
because fault current can flow either direction; a plain non-directional
overcurrent relay can misoperate or fail to operate depending on which
source is feeding the fault. Pair with
interconnection-impact-mitigationwhen new DER changes fault-current direction or magnitude.
-
Document settings and margins. Write the final pickup, time-dial/ curve-type, and instantaneous settings for every device, with the coordination margin achieved at the minimum and maximum fault current in its zone, into a coordination study report. This becomes the commissioning record the relay technician sets the device to.
Data sources
- Relay/breaker/fuse manufacturer TCC curves and setting manuals (search " time current curve" or " instruction manual").
- IEC 60255-151 / IEEE C37.112 for standard inverse-time curve coefficients.
- CT accuracy class and saturation data from the CT manufacturer's datasheet (ratio, class, knee-point voltage).
- Utility interconnection requirements (often specify minimum/maximum short-circuit contribution, required protection functions, and coordination margin) from the local utility's interconnection standard.
Prerequisites
- Fault-current magnitudes (maximum and minimum) at every bus/zone in scope,
from a completed short-circuit study — see
surge,pandapower, or the PowerMCP-backedpsse/pslf/powerworldskills, or a dedicated ANSI/IEC short-circuit program. python3withnumpyandmatplotlibforscripts/tcc_plot.pyandscripts/coordination_plot.py.- The actual device TCC data (coefficient table or digitized curve) for every device in the chain; a generic "typical" curve is not a substitute for the installed device's actual setting.
Limitations
- This skill does not run a short-circuit study itself; it consumes one. An error in the upstream fault-current calculation (wrong source impedance, missing contribution from DER or motors) propagates directly into a wrong coordination verdict.
- IEC and ANSI/IEEE short-circuit calculation methods can give materially different fault-current magnitudes for the same network (different treatment of pre-fault voltage, X/R ratio, and multiplying factors); mixing results from different methods across one coordination study produces an inconsistent result. Use one method consistently and say which.
scripts/tcc_plot.py's built-in IEC/IEEE curve formulas assume the relay implements the standard curve exactly; some electromechanical or older solid-state relays deviate from the textbook formula and need their actual published curve digitized instead.- Coordination margins and curve shapes do not capture everything a full arc-flash or protection-and-control (P&C) engineering review would: CT/PT wiring polarity, trip-circuit supervision, breaker failure protection, and communications-based schemes (e.g. teleprotection) are outside this skill's scope and need a licensed protection engineer's review before commissioning.
- This is a planning/engineering aid, not a substitute for the utility's or jurisdiction's mandatory protection-coordination review and sign-off where one is required.
Quality checks before sign-off
- Every adjacent device pair in the protection chain has a documented selectivity margin (with the specific margin value used and its source) across the full minimum-to-maximum fault-current range of its zone.
- Every device's pickup setting is below the minimum fault current its zone must sense, and above the maximum normal load/inrush current it must ride through — both checked explicitly, not just one.
- Every device's rating exceeds the maximum fault current at its location
(cross-checked against
short-circuit-mitigationif any margin is tight). - CT saturation and directionality checked for any device on a multi-source or ring topology, not assumed away.
- The short-circuit method (ANSI or IEC) used for the underlying fault currents is stated in the report, and consistent throughout.
示例提示词
帮我检查这几级保护装置的时间电流曲线有没有选择性配合问题。
所属插件
安装该插件会一并获得同领域的 63 个 Skill / MCP。
同插件的其他科研 Skill
- ANDES电力系统动态仿真Runs ANDES power-system dynamic studies via PowerMCP: power flow, eigenvalue analysis, and time-domain simulation. Use for damping, stability, or oscillation-mode questions.
- 电池选型与电源预算Builds an evidence-tagged power budget and sizes a manufacturable battery with pouch outline, seals, and derating. Use when sizing runtime, mAh, charging, or supply rails.
- FPGA比特流生成与烧录Generates a Xilinx FPGA bitstream and programs it over JTAG, or burns an MCS image into flash for power-on boot. Use when flashing a board or diagnosing boot failures.
- 硬件项目发布包组装Assembles a hardware release package (fab files, BOM/CPL, carts, assembly guide, hashed manifest) and runs a ready-to-build gate. Use before ordering prototypes.
- 时钟域交叉风险审查Audits clock-domain-crossing risk on an FPGA design and applies the smallest safe synchronizer or constraint fix. Use to resolve CDC violations before sign-off.
- 硬件产品认证合规规划Plans certifications a hardware product needs per target market (FCC, CE/RED, UKCA, battery/radio rules), with cost and lead-time estimates. Use before PCB or enclosure tooling.
- Vivado XDC时序约束编写Authors a Vivado XDC timing constraint set from scratch: clocks, I/O delays, and timing exceptions. Use first, before timing closure, on a design with no or incomplete constraints.
- N-1/N-2应急违规处置Playbook for N-1/N-2 contingency violations: ranks contingencies and proposes preventive and corrective actions. Use after a study shows voltage or thermal problems.
- 潮流计算不收敛诊断Playbook for power-flow convergence failures in PSS/E, PSLF, PowerWorld, pandapower, PyPSA, surge, or OpenDSS. Use when a case diverges or fails to solve.
- 硬件成本核算与采购Prices a hardware product at multiple volumes with one-time vs per-unit cost, landed cost per country, and sourcing leads. Use to estimate unit cost before a pitch.
- RTL仿真覆盖率收敛Measures RTL simulation code coverage and iteratively closes it toward a target by adding testbench stimulus. Use for a sign-off-grade coverage report.
- 配电网DER接纳能力治理Playbook for distribution DER hosting-capacity limits: voltage rise, reverse flow, and thermal limits from PV and storage. Use to estimate how much DER a feeder can host.
- 电子电路设计与审查Designs, audits, or corrects an electronic circuit from a brief, schematic, or netlist, checking power domains, reset sequencing, and ratings. Use for circuit review.
- 硬件可制造性红队审查Red-team audit that fix-loops a hardware project to ready-to-build, re-deriving parts, rails, battery physics, and cost. Use for a reality check before committing to a design.
- 电力系统动态稳定处置Playbook for dynamic stability problems: poor damping, angle instability, or sustained oscillations from eigenvalue or time-domain studies. Use after an unstable study result.
- Egret电力市场调度优化Runs Egret market/operations optimization (DC-OPF, AC-OPF, unit commitment) via PowerMCP. Use for cheapest dispatch, unit commitment, or congestion checks.
- 电子元器件选型核查Researches electronic components against primary sources: part numbers, datasheet limits, lifecycle, stock, and price breaks, one dossier per part. Use to verify or source a BOM.
- EMC电磁兼容预测试Plans grounding, shielding, and filtering for EMC/EMI, and runs an emissions pre-scan with a root-cause fix sequence. Use before a lab test or after a failed EMI scan.
- 产品外壳参数化建模Designs a hardware enclosure as parametric CAD with STEP/STL/GLB output, a DFM check, and Blender assembly validation. Use when designing a case or checking fit.
- 电网频率响应问题处置Playbook for frequency problems: low inertia, high RoCoF, weak primary response, or UFLS risk after loss of the largest unit. Use when a study flags frequency issues.
- FPGA RTL到比特流全流程Drives a Xilinx FPGA design end to end through RTL, simulation, synthesis, implementation, and bitstream, gated at every stage. Use to run the complete build flow in one pass.
- 硬件产品全流程总协调Leads a physical electronic product from idea to a doable design, coordinating specs, parts, battery, PCB, enclosure, render, and cost sub-skills. Use starting a hardware product.
- 硬件原理图与BOM审查Reviews hardware projects: checks schematics against datasheets, pin connections, and firmware-to-hardware alignment across KiCad/Altium files. Use for a design alignment check.
- FPGA ILA在线逻辑调试Inserts an Integrated Logic Analyzer, programs the board, arms a trigger, and reads captured waveforms on real FPGA hardware. Use when sim passes but the board fails.
常见问题
继电保护级差整定能做什么?
Checks relay/breaker/fuse time-current coordination and selectivity margins from short-circuit results. Use when sizing protective devices or diagnosing a miscoordination。
如何安装继电保护级差整定?
在科搭 Codar 左侧点击「插件」,在「组件」页签搜索「继电保护级差整定」并安装;在 Claude Code 或 Codex 中可以发送本页的安装提示词,或下载 Skill 包后解压到 ~/.claude/skills 或 ~/.codex/skills。
继电保护级差整定需要哪些权限?
该科研 Skill没有声明额外权限;执行具体操作时仍由 Agent 按自身规则请求确认。
继电保护级差整定经过官方审核吗?
是。SpeedSkills 收录的每个版本都会记录内容摘要与权限声明,当前版本已通过安全审核。