科研 Skill
电子电路设计与审查
design-and-review-circuit
Designs, audits, or corrects an electronic circuit from a brief, schematic, or netlist, checking power domains, reset sequencing, and ratings. Use for circuit review.
SKILL.md
Circuit Design Reviewer
Treat readability and electrical correctness as separate gates. Default to review-only unless the user asks to change the authoritative circuit source.
Establish truth
- Read repository instructions, product brief, architecture, sourcing lock, native schematic or generator, netlist, BOM, datasheets, firmware-visible behavior, and existing review notes.
- Identify the electrical source of truth. When a generator owns the schematic, modify the generator rather than only generated files.
- Capture ERC/lint, connectivity, and protected PCB/layout hashes before any authorized correction.
- Use official manufacturer documents for exact orderable parts. Browse when datasheets, standards, availability, or current guidance can have changed.
- Select the evidence path in references/evidence-adapters.md; never claim an edit or verification stronger than the source permits.
Audit
Read references/circuit-audit-checklist.md
and produce .pcba-workflow/circuit-review.md from
assets/circuit-review.md.
- Explain operating principle and data/power/control flow in plain language.
- Build a component-by-component function table, power tree, voltage-domain table, operating-state table, and reset/boot/ownership sequence.
- Trace every external interface, power entry, driver, receiver, memory/control path, and hardware default. Check partial-power and firmware-not-running states.
- Verify ratings, logic thresholds, enable polarity, unused pins, static ties, decoupling, regulator stability/thermal margin, protection, clocks/timing, and connector semantics.
- Classify each finding as critical, major, minor, or information; distinguish proven defect, design risk, and unknown evidence.
- Record layout constraints using
[SPEC],[TARGET], or[TBD-MEASURE]. Include data/edge rate, topology and stubs, return plane, skew intent, current allocation, placement, keepout, and authoritative source where applicable.
Correct only when authorized
For each change, state the defect and evidence, edit the source of truth, render the complete schematic, inspect it visually, rerun ERC/lint, compare canonical connectivity, and confirm protected layout files remain unchanged. A deliberate electrical change must appear explicitly in the connectivity delta and design decision record; do not hide it inside presentation cleanup.
Gate
Use PASS only when no critical/major issue or safety-relevant unknown remains
and the selected parts match the sourcing lock. Use USER_REVIEW for explicit
engineering decisions and BLOCKED for missing evidence or a failed check.
Hand drawing readability to $schematic-humanizer, part risk to
$qualify-pcba-sourcing, and placement/routing constraints to
$pcb-layout-review.
示例提示词
帮我审查一下这份原理图的电源时序和复位逻辑有没有问题。
所属插件
安装该插件会一并获得同领域的 63 个 Skill / MCP。
同插件的其他科研 Skill
- ANDES电力系统动态仿真Runs ANDES power-system dynamic studies via PowerMCP: power flow, eigenvalue analysis, and time-domain simulation. Use for damping, stability, or oscillation-mode questions.
- 电池选型与电源预算Builds an evidence-tagged power budget and sizes a manufacturable battery with pouch outline, seals, and derating. Use when sizing runtime, mAh, charging, or supply rails.
- FPGA比特流生成与烧录Generates a Xilinx FPGA bitstream and programs it over JTAG, or burns an MCS image into flash for power-on boot. Use when flashing a board or diagnosing boot failures.
- 硬件项目发布包组装Assembles a hardware release package (fab files, BOM/CPL, carts, assembly guide, hashed manifest) and runs a ready-to-build gate. Use before ordering prototypes.
- 时钟域交叉风险审查Audits clock-domain-crossing risk on an FPGA design and applies the smallest safe synchronizer or constraint fix. Use to resolve CDC violations before sign-off.
- 硬件产品认证合规规划Plans certifications a hardware product needs per target market (FCC, CE/RED, UKCA, battery/radio rules), with cost and lead-time estimates. Use before PCB or enclosure tooling.
- Vivado XDC时序约束编写Authors a Vivado XDC timing constraint set from scratch: clocks, I/O delays, and timing exceptions. Use first, before timing closure, on a design with no or incomplete constraints.
- N-1/N-2应急违规处置Playbook for N-1/N-2 contingency violations: ranks contingencies and proposes preventive and corrective actions. Use after a study shows voltage or thermal problems.
- 潮流计算不收敛诊断Playbook for power-flow convergence failures in PSS/E, PSLF, PowerWorld, pandapower, PyPSA, surge, or OpenDSS. Use when a case diverges or fails to solve.
- 硬件成本核算与采购Prices a hardware product at multiple volumes with one-time vs per-unit cost, landed cost per country, and sourcing leads. Use to estimate unit cost before a pitch.
- RTL仿真覆盖率收敛Measures RTL simulation code coverage and iteratively closes it toward a target by adding testbench stimulus. Use for a sign-off-grade coverage report.
- 配电网DER接纳能力治理Playbook for distribution DER hosting-capacity limits: voltage rise, reverse flow, and thermal limits from PV and storage. Use to estimate how much DER a feeder can host.
- 硬件可制造性红队审查Red-team audit that fix-loops a hardware project to ready-to-build, re-deriving parts, rails, battery physics, and cost. Use for a reality check before committing to a design.
- 电力系统动态稳定处置Playbook for dynamic stability problems: poor damping, angle instability, or sustained oscillations from eigenvalue or time-domain studies. Use after an unstable study result.
- Egret电力市场调度优化Runs Egret market/operations optimization (DC-OPF, AC-OPF, unit commitment) via PowerMCP. Use for cheapest dispatch, unit commitment, or congestion checks.
- 电子元器件选型核查Researches electronic components against primary sources: part numbers, datasheet limits, lifecycle, stock, and price breaks, one dossier per part. Use to verify or source a BOM.
- EMC电磁兼容预测试Plans grounding, shielding, and filtering for EMC/EMI, and runs an emissions pre-scan with a root-cause fix sequence. Use before a lab test or after a failed EMI scan.
- 产品外壳参数化建模Designs a hardware enclosure as parametric CAD with STEP/STL/GLB output, a DFM check, and Blender assembly validation. Use when designing a case or checking fit.
- 电网频率响应问题处置Playbook for frequency problems: low inertia, high RoCoF, weak primary response, or UFLS risk after loss of the largest unit. Use when a study flags frequency issues.
- FPGA RTL到比特流全流程Drives a Xilinx FPGA design end to end through RTL, simulation, synthesis, implementation, and bitstream, gated at every stage. Use to run the complete build flow in one pass.
- 硬件产品全流程总协调Leads a physical electronic product from idea to a doable design, coordinating specs, parts, battery, PCB, enclosure, render, and cost sub-skills. Use starting a hardware product.
- 硬件原理图与BOM审查Reviews hardware projects: checks schematics against datasheets, pin connections, and firmware-to-hardware alignment across KiCad/Altium files. Use for a design alignment check.
- FPGA ILA在线逻辑调试Inserts an Integrated Logic Analyzer, programs the board, arms a trigger, and reads captured waveforms on real FPGA hardware. Use when sim passes but the board fails.
- 新能源并网影响评估Playbook for screening the grid impact of a new generator, storage, or large-load interconnection. Use to check whether a given MW can connect and what upgrades it needs.
常见问题
电子电路设计与审查能做什么?
Designs, audits, or corrects an electronic circuit from a brief, schematic, or netlist, checking power domains, reset sequencing, and ratings. Use for circuit review。
如何安装电子电路设计与审查?
在科搭 Codar 左侧点击「插件」,在「组件」页签搜索「电子电路设计与审查」并安装;在 Claude Code 或 Codex 中可以发送本页的安装提示词,或下载 Skill 包后解压到 ~/.claude/skills 或 ~/.codex/skills。
电子电路设计与审查需要哪些权限?
该科研 Skill没有声明额外权限;执行具体操作时仍由 Agent 按自身规则请求确认。
电子电路设计与审查经过官方审核吗?
是。SpeedSkills 收录的每个版本都会记录内容摘要与权限声明,当前版本已通过安全审核。