科研 Skill
泵型选型决策树
pump-selection-helper
Walks a decision tree for selecting pump type (centrifugal, mixed/axial flow, or positive displacement) based on flow, head, and fluid properties. Use early in pump selection before detailed design.
SKILL.md
Pump Selection Helper
A practical decision-tree tool for selecting the appropriate pump type based on operating conditions, flow requirements, head, and fluid properties.
Pump Type Overview
Centrifugal Pumps (Dynamic)
Radial Flow (Centrifugal)
- Flow range: 10 - 100,000 gpm (0.6 - 6,300 L/s)
- Head range: 50 - 5,000 ft (15 - 1,500 m)
- Specific speed (Ns): 500 - 4,000 (US units)
- Applications: General purpose, high head, moderate to high flow
- Advantages: Simple, reliable, low maintenance, handles solids
- Limitations: Poor efficiency at low flow, not suitable for high viscosity
Mixed Flow
- Flow range: 500 - 20,000 gpm (30 - 1,260 L/s)
- Head range: 20 - 200 ft (6 - 60 m)
- Specific speed (Ns): 4,000 - 9,000 (US units)
- Applications: Irrigation, flood control, water supply
- Advantages: Good efficiency, handles moderate flow and head
- Limitations: Limited head capability
Axial Flow (Propeller)
- Flow range: 2,000 - 100,000 gpm (125 - 6,300 L/s)
- Head range: 5 - 50 ft (1.5 - 15 m)
- Specific speed (Ns): 9,000 - 15,000 (US units)
- Applications: Circulation, cooling water, drainage
- Advantages: Very high flow, compact
- Limitations: Low head only, sensitive to flow variations
Positive Displacement Pumps
Gear Pumps
- Flow range: 1 - 1,500 gpm (0.06 - 95 L/s)
- Pressure range: Up to 3,000 psi (200 bar)
- Viscosity range: 1 - 1,000,000 cP
- Applications: Lubrication oils, fuel transfer, hydraulics
- Advantages: Self-priming, handles viscous fluids, constant flow
- Limitations: Cannot handle abrasives, pulsating flow
Piston/Plunger Pumps
- Flow range: 0.1 - 5,000 gpm (0.006 - 315 L/s)
- Pressure range: Up to 50,000 psi (3,400 bar)
- Viscosity range: 1 - 100,000 cP
- Applications: High-pressure cleaning, oil/gas, chemical injection
- Advantages: Very high pressure, accurate metering
- Limitations: Pulsating flow, high maintenance, expensive
Diaphragm Pumps
- Flow range: 0.1 - 800 gpm (0.006 - 50 L/s)
- Pressure range: Up to 1,000 psi (70 bar)
- Applications: Corrosive chemicals, slurries, hazardous fluids
- Advantages: Seal-less, handles abrasives and solids
- Limitations: Limited pressure, pulsating flow
Screw Pumps (Progressive Cavity)
- Flow range: 1 - 2,000 gpm (0.06 - 125 L/s)
- Pressure range: Up to 1,500 psi (100 bar)
- Viscosity range: 1 - 1,000,000 cP
- Applications: Viscous fluids, slurries, shear-sensitive fluids
- Advantages: Non-pulsating, handles high viscosity, gentle pumping
- Limitations: Wear on rotor/stator, limited to moderate pressure
Specialty Pumps
Turbine Pumps (Vertical)
- Flow range: 50 - 10,000 gpm (3 - 630 L/s)
- Head range: 50 - 1,000 ft (15 - 300 m)
- Applications: Deep wells, booster stations, cooling towers
- Advantages: Space-efficient, handles high head
- Limitations: Complex installation, difficult maintenance
Jet Pumps
- Flow range: 5 - 100 gpm (0.3 - 6.3 L/s)
- Head range: 50 - 300 ft (15 - 90 m)
- Applications: Shallow/deep wells, remote locations
- Advantages: No moving parts in fluid, simple
- Limitations: Low efficiency (25-35%)
Airlift Pumps
- Flow range: 10 - 5,000 gpm (0.6 - 315 L/s)
- Applications: Wells, wastewater, sand/gravel
- Advantages: Simple, handles solids and corrosives
- Limitations: Very low efficiency, requires air compressor
Selection Criteria
1. Flow Rate Requirements
- Low flow (< 10 gpm / 0.6 L/s): Positive displacement preferred
- Medium flow (10 - 1,000 gpm / 0.6 - 63 L/s): Centrifugal or PD
- High flow (> 1,000 gpm / 63 L/s): Centrifugal (mixed or axial flow)
2. Head Requirements
- Low head (< 50 ft / 15 m): Axial flow centrifugal or PD
- Medium head (50 - 500 ft / 15 - 150 m): Radial centrifugal or PD
- High head (> 500 ft / 150 m): High-speed centrifugal or piston pumps
3. Specific Speed (Ns)
Specific speed determines the pump impeller type:
US Units: Ns = N × √Q / H^0.75 SI Units: Ns = N × √Q / H^0.75
Where:
- N = rotational speed (rpm)
- Q = flow rate (gpm or m³/h)
- H = head (ft or m)
Classification:
- Ns < 2,000: Radial flow (high head, low flow)
- Ns = 2,000 - 5,000: Francis vane (medium head/flow)
- Ns = 5,000 - 10,000: Mixed flow
- Ns > 10,000: Axial flow (low head, high flow)
4. Fluid Viscosity Effects
Low viscosity (< 100 cP):
- Centrifugal pumps work well
- No significant correction needed
Medium viscosity (100 - 1,000 cP):
- Centrifugal efficiency drops
- Consider positive displacement
- Apply viscosity corrections
High viscosity (> 1,000 cP):
- Positive displacement required
- Gear, screw, or piston pumps
- Centrifugal pumps ineffective
5. NPSH Requirements
Net Positive Suction Head prevents cavitation:
- NPSHa (Available) = Atmospheric pressure + Static head - Vapor pressure - Friction losses
- NPSHr (Required) = From pump curve (manufacturer data)
- Requirement: NPSHa > NPSHr + Safety margin (3-5 ft)
High NPSHr concerns:
- Use double suction impeller
- Lower pump speed
- Use inducer or booster pump
- Positive displacement (self-priming)
6. Efficiency Considerations
Best Efficiency Point (BEP):
- Centrifugal: Operate within 70-120% of BEP flow
- Peak efficiency: 60-85% for centrifugal
- PD pumps: 70-90% (less flow-dependent)
Energy cost calculation: Annual cost = (BHP × 0.746 × Operating hours × kWh rate) / Efficiency
7. Cost Factors
Initial Cost:
- Centrifugal: $$ (lowest)
- Gear/Screw: $$$ (moderate)
- Piston/Plunger: $$$$ (highest)
Operating Cost:
- Energy consumption
- Maintenance frequency
- Spare parts availability
Life Cycle Cost = Initial + Installation + Energy + Maintenance + Downtime
Decision Tree for Pump Selection
START
|
├─ Is fluid viscosity > 1,000 cP?
| YES → POSITIVE DISPLACEMENT
| ├─ High pressure (> 1,000 psi)? → PISTON/PLUNGER
| ├─ Shear-sensitive? → SCREW PUMP
| ├─ Abrasive/corrosive? → DIAPHRAGM
| └─ General viscous? → GEAR PUMP
|
NO ↓
|
├─ Is constant flow required despite pressure changes?
| YES → POSITIVE DISPLACEMENT (Gear, Piston, or Screw)
|
NO ↓
|
├─ Calculate Specific Speed: Ns = N × √Q / H^0.75
|
├─ Ns < 500? (Very high head, low flow)
| YES → TURBINE or HIGH-SPEED CENTRIFUGAL
|
├─ Ns = 500 - 4,000? (High head, moderate flow)
| YES → RADIAL CENTRIFUGAL
| ├─ Deep well? → VERTICAL TURBINE
| └─ Surface? → HORIZONTAL CENTRIFUGAL
|
├─ Ns = 4,000 - 9,000? (Moderate head, high flow)
| YES → MIXED FLOW CENTRIFUGAL
|
├─ Ns > 9,000? (Low head, very high flow)
| YES → AXIAL FLOW (PROPELLER)
|
└─ Special Conditions?
├─ Self-priming required? → PD or JET PUMP
├─ No electricity available? → ENGINE-DRIVEN
├─ Solids > 10% by volume? → DIAPHRAGM or SCREW
└─ Metering accuracy critical? → PISTON or DIAPHRAGM
Application-Specific Recommendations
Water Supply
- Municipal: Horizontal split-case centrifugal (high reliability)
- Wells: Vertical turbine or submersible
- Booster: Multistage centrifugal
- Typical: Q = 100-5,000 gpm, H = 50-500 ft
HVAC/Cooling
- Chilled water: End-suction or inline centrifugal
- Condenser water: Horizontal split-case
- Typical: Q = 50-2,000 gpm, H = 30-150 ft
Chemical Processing
- Corrosive: Lined centrifugal or diaphragm
- Viscous: Gear or screw pumps
- Metering: Diaphragm or piston
- Typical: Q = 1-500 gpm, P = 50-500 psi
Oil & Gas
- Transfer: Centrifugal or screw
- Injection: High-pressure piston
- Crude oil: Screw pumps (viscous)
- Typical: Q = 10-1,000 gpm, P = 100-5,000 psi
Wastewater
- Raw sewage: Submersible non-clog centrifugal
- Sludge: Progressive cavity (screw)
- Chemical feed: Diaphragm metering
- Typical: Q = 50-5,000 gpm, H = 20-200 ft
Agriculture/Irrigation
- Surface water: Horizontal centrifugal
- Wells: Vertical turbine
- Drip irrigation: Centrifugal with filtration
- Typical: Q = 100-5,000 gpm, H = 50-300 ft
Mining/Slurry
- Heavy slurry: Horizontal slurry pump (rubber-lined)
- Abrasive: Hard-metal or ceramic-lined
- Dewatering: Submersible or horizontal centrifugal
- Typical: Q = 100-10,000 gpm, H = 50-500 ft
Food & Beverage
- Sanitary: Centrifugal (polished, 3A certified)
- Viscous products: Lobe or screw pumps
- CIP/Cleaning: Centrifugal
- Typical: Q = 10-500 gpm, P = 50-150 psi
Usage Guide
Using selector.py
Run the interactive selector:
python selector.py
Or use programmatically:
from selector import select_pump, calculate_specific_speed
# Example 1: Water supply
result = select_pump(
flow_rate=500, # gpm
head=200, # ft
viscosity=1, # cP
fluid_type="water",
speed=1750 # rpm
)
print(result)
# Example 2: High viscosity
result = select_pump(
flow_rate=50,
head=100,
viscosity=5000,
fluid_type="oil",
temp=100 # °F
)
print(result)
Quick Selection Guidelines
- Start with flow and head - These are primary factors
- Check fluid properties - Viscosity, corrosiveness, abrasiveness
- Calculate specific speed - Determines centrifugal type
- Verify NPSH - Ensure adequate suction conditions
- Consider operating range - Pump should operate near BEP
- Evaluate life cycle cost - Not just initial cost
- Check maintenance access - Space for service
- Review manufacturer curves - Verify actual performance
Common Mistakes to Avoid
- ❌ Oversizing pumps (reduces efficiency, increases cost)
- ❌ Ignoring viscosity effects on centrifugal pumps
- ❌ Insufficient NPSH margin (causes cavitation)
- ❌ Operating far from BEP (premature wear)
- ❌ Selecting based on initial cost only
- ❌ Not considering future expansion needs
- ❌ Ignoring system curve changes
References
See reference.md for:
- Detailed pump selection charts
- Specific speed ranges from industry standards
- Manufacturer selection guides
- Performance curve examples
- NPSH calculation methods
示例提示词
给定流量扬程和介质特性,帮我判断该选哪种类型的泵。
所属插件
安装该插件会一并获得同领域的 36 个 Skill / MCP。
同插件的其他科研 Skill
- ANSYS Fluent CFD仿真自动化Automates ANSYS Fluent CFD setup, meshing, and batch runs via Python scripting, journal files, and the PyAnsys ecosystem. Use when a user wants to script or automate an ANSYS Fluent simulation.
- Cantera燃烧仿真Runs Cantera combustion simulations: flame temperature, ignition delay, laminar flame speed, PSR. Use for mechanism-based combustion analysis tasks.
- 离心泵气蚀风险评估Calculates NPSHa and NPSHr and assesses cavitation risk for centrifugal pumps, with prevention and detection guidance. Use when sizing suction piping or diagnosing pump cavitation.
- 气蚀评估物性数据库Looks up vapor pressure, NPSHr data, and correlations for cavitation risk assessment in pumps. Use when cavitation-analysis needs reference property or NPSHr data.
- 离心泵设计计算Designs centrifugal pumps from first principles using Euler equations, velocity triangles, and specific speed. Use for impeller sizing or new centrifugal pump design.
- COMSOL多物理场耦合仿真Sets up coupled fluid-structure interaction simulations in COMSOL Multiphysics, focused on pump vibration analysis. Use when a user wants to script or automate a COMSOL FSI model.
- CoolProp流体物性查询Queries thermodynamic and transport properties for 100+ pure and pseudo-pure fluids via the CoolProp library. Use when a calculation needs fluid density, viscosity, or enthalpy data.
- 工程计算环境初始化Sets up a Python session with engineering constants, Pint units, and plotting defaults. Use at the start of a calculation session.
- 流体计算数值错误校验Handles common numerical errors in fluid calculations, such as division by zero and out-of-range physical values, with validation checks. Use when fluid code fails or returns unphysical results.
- 流体力学分析工作流Guides a systematic fluid dynamics analysis from problem setup and domain definition through model selection to validation. Use when planning a CFD or analytical fluid mechanics study end to end.
- 经验公式流体物性速算Computes quick fluid property estimates (density, viscosity, vapor pressure) from empirical correlations without needing a database. Use for fast order-of-magnitude property checks.
- 管道流动与泵选型计算Computes pipe flow, pump sizing, friction factor, and compressible flow results with the fluids Python package. Use for quick, code-based fluid mechanics calculations.
- 工程工具与数据库清点Enumerates installed Python packages, databases, and simulation tools available in the current environment. Use at the start of a session to avoid recommending unavailable tools.
- 管路元件损失系数查询Looks up loss coefficients (K-values) and equivalent lengths for pipes, valves, and fittings in pump and piping systems. Use when computing system head loss.
- 流体与材料物性查询Looks up temperature-dependent fluid viscosities, densities, and other material properties for pump and heat-transfer calculations. Use when a calculation needs property data at a given temperature.
- 泵性能曲线绘制Creates professional engineering plots such as pump performance curves, CFD velocity contours, and publication-quality figures with matplotlib. Use when a result needs a plotted figure.
- NASA大气与航空流体数据Accesses atmospheric property profiles and standard-atmosphere models from NASA Earthdata for high-altitude and aerospace fluid analysis. Use when a task needs altitude-dependent atmospheric data.
- 管网图论建模Models hydraulic piping networks and multi-pump systems as graphs using NetworkX flow algorithms. Use for analyzing flow distribution across a branched or looped piping network.
- REFPROP高精度物性查询Queries high-accuracy thermodynamic and transport properties from the commercial NIST REFPROP database. Use when a calculation needs reference-quality fluid property data and REFPROP is licensed.
- 数值数组计算Performs numerical array operations with NumPy: velocity field processing, pump curve interpolation, linear systems, and matrix methods. Use for general numerical computation in engineering code.
- OpenFOAM仿真与后处理Runs and post-processes OpenFOAM CFD simulations with PyFoam, pyvista, and vtk for mesh setup, solver control, and visualization. Use for scripted OpenFOAM workflows outside ParaView.
- 泵性能曲线与相似定律Generates and interprets pump H-Q/efficiency/power/NPSH curves, applies affinity laws, and predicts off-design performance. Use for pump curve analysis.
- 工程单位换算与量纲分析Handles engineering units with automatic conversion and dimensional-consistency checking using the Pint library. Use whenever a calculation mixes units or needs unit safety.
- 容积式泵设计分析Designs and analyzes gear, piston, and screw positive-displacement pumps, including volumetric efficiency and slip. Use when the pump is positive-displacement rather than centrifugal.
常见问题
泵型选型决策树能做什么?
Walks a decision tree for selecting pump type (centrifugal, mixed/axial flow, or positive displacement) based on flow, head, and fluid properties. Use early in pump selection before detailed design。
如何安装泵型选型决策树?
在科搭 Codar 左侧点击「插件」,在「组件」页签搜索「泵型选型决策树」并安装;在 Claude Code 或 Codex 中可以发送本页的安装提示词,或下载 Skill 包后解压到 ~/.claude/skills 或 ~/.codex/skills。
泵型选型决策树需要哪些权限?
该科研 Skill没有声明额外权限;执行具体操作时仍由 Agent 按自身规则请求确认。
泵型选型决策树经过官方审核吗?
是。SpeedSkills 收录的每个版本都会记录内容摘要与权限声明,当前版本已通过安全审核。