科研 Skill
离心泵设计计算
centrifugal-pump-design
Designs centrifugal pumps from first principles using Euler equations, velocity triangles, and specific speed. Use for impeller sizing or new centrifugal pump design.
SKILL.md
Centrifugal Pump Design
Overview
This skill provides a comprehensive workflow for designing centrifugal pumps from first principles using Euler turbine equations, velocity triangles, and dimensionless parameters. The methodology follows classical pump design theory as presented in Stepanoff, Gülich, and Karassik.
Design Workflow
1. Requirements Analysis
Input Parameters:
- Flow rate: Q (m³/s or m³/h)
- Head: H (m)
- Rotational speed: N (rpm)
- Fluid properties:
- Density: ρ (kg/m³)
- Kinematic viscosity: ν (m²/s)
- NPSH available (m)
Derived Parameters:
- Power requirement: P = ρ·g·Q·H / η
- Specific speed: Ns = N·√Q / H^0.75 (dimensionless form)
- Suction specific speed: S = N·√Q / NPSH^0.75
2. Specific Speed Calculation and Pump Type Selection
Specific Speed Definition:
The specific speed is a dimensionless parameter that characterizes pump geometry:
Ns = (N·Q^0.5) / H^0.75
Where:
- N = rotational speed (rpm)
- Q = flow rate (m³/s)
- H = head per stage (m)
Pump Type Selection Based on Ns:
| Specific Speed (Ns) | Pump Type | Impeller Shape | Typical Efficiency |
|---|---|---|---|
| 10-30 | Radial flow | Narrow, radial | 70-85% |
| 30-50 | Francis-vane | Medium width | 80-88% |
| 50-80 | Mixed flow | Wide, angled | 85-90% |
| 80-150 | Mixed flow | Very wide | 85-92% |
| 150-300 | Axial flow | Propeller | 82-88% |
Note: Specific speed units vary by convention. The European convention uses:
nq = N·√Q / H^0.75 [where Q in m³/s, H in m, N in rpm]
US convention multiplies by different constants. Always verify which convention is being used.
3. Impeller Diameter Estimation
Stepanoff Correlation for Outlet Diameter:
D2 = 84.6 · (H / N)^0.5 [D2 in mm, H in m, N in rpm]
Or in SI units:
D2 = K · (H·g / u2²)^0.5 · u2 / (0.5·π·N/60)
Simplified form:
D2 = 60 / π · √(2·g·H / Ku²) / N [D2 in m]
Where Ku is the outlet velocity coefficient (typically 0.95-1.05)
Outlet Width Estimation:
b2 = K_b · D2 / Ns^0.65
Where K_b = 2.5-3.5 for radial pumps
Eye Diameter Estimation:
Based on suction specific speed:
D_eye = (4·Q / (π·c_m1))^0.5
Where c_m1 is the meridional velocity at inlet (typically 2-4 m/s)
4. Velocity Triangle Construction
Velocity Components:
At any point in the impeller:
- u = blade velocity (tangential)
- c = absolute fluid velocity
- w = relative velocity (fluid velocity relative to blade)
Velocity Triangle Relations:
c = u + w (vector addition)
Component breakdown:
- c_m = meridional (through-flow) component
- c_u = tangential (whirl) component
- u = ω·r = π·N·D/60
Inlet Triangle (Station 1 - Eye):
For axial inlet with no pre-rotation:
c_u1 = 0 (design condition)
c_m1 = Q / A1 = Q / (π·D_eye²/4)
c1 = c_m1
u1 = π·N·D_eye/60
w1 = √(u1² + c_m1²)
β1 = atan(c_m1 / u1) [blade angle at inlet]
Outlet Triangle (Station 2):
u2 = π·N·D2/60
c_m2 = Q / A2 = Q / (π·D2·b2)
From Euler equation and design choices:
c_u2 = g·H / u2 (for backward-curved blades)
c2 = √(c_m2² + c_u2²)
w2 = √((u2 - c_u2)² + c_m2²)
β2 = atan(c_m2 / (u2 - c_u2)) [blade angle at outlet]
Important: β2 is typically 15-35° for backward-curved blades
5. Euler Turbine Equation Application
Fundamental Equation:
The theoretical head developed by a pump is:
H_th = (u2·c_u2 - u1·c_u1) / g
For radial entry (c_u1 = 0):
H_th = u2·c_u2 / g
In terms of blade angles:
H_th = u2² / g - u2·c_m2 / (g·tan(β2))
Slip Factor Correction:
Real pumps have finite number of blades, causing slip:
σ = 1 - (π·sin(β2)) / Z
Where Z is the number of blades (typically 5-9 for radial pumps)
Actual head:
H = σ·H_th
6. Blade Angle Calculations
Inlet Blade Angle (β1):
β1 = atan(c_m1 / u1)
Typically: β1 = 15-30° for radial pumps
Outlet Blade Angle (β2):
β2 = atan(c_m2 / (u2 - c_u2))
Blade Type Selection:
- Backward-curved: β2 < 90° (most common, stable operation)
- Radial: β2 = 90° (higher head, less stable)
- Forward-curved: β2 > 90° (rarely used, unstable)
Blade Number Selection:
Pfleiderer formula:
Z = 6.5 · (D2 + D1)/(D2 - D1) · sin((β1 + β2)/2)
Round to nearest integer (typically 5-9 blades)
7. Efficiency Estimation
Component Efficiencies:
Total efficiency:
η = η_h · η_vol · η_mech
Hydraulic Efficiency (η_h):
Accounts for friction and shock losses:
η_h = H / H_th ≈ 0.85-0.95
More detailed (Gülich):
η_h = 1 / (1 + k_friction + k_shock + k_recirculation)
Volumetric Efficiency (η_vol):
Accounts for leakage:
η_vol = Q / (Q + Q_leak) ≈ 0.96-0.99
Mechanical Efficiency (η_mech):
Accounts for bearing and seal friction:
η_mech = (P_hydraulic) / (P_shaft) ≈ 0.95-0.98
Overall Efficiency Estimation:
For preliminary design (Gülich correlation):
η_opt ≈ 0.94 - 0.0525·(Ns)^(-0.5) [for Ns in European units]
Or Anderson correlation:
η = 1 - 0.8 / (Ns/50)^0.25 [for well-designed pumps]
8. Performance Curve Generation
Head-Flow Characteristic:
The H-Q curve can be approximated as:
H = a·Q² + b·Q + c
Where coefficients are determined from:
- Design point (Q, H)
- Shut-off head (Q=0, H_max)
- Slope at design point
Power Curve:
P = ρ·g·Q·H / η(Q)
NPSH Required:
NPSH_req = (c1²)/(2g) + k·(c1²)/(2g)
Where k accounts for acceleration and losses (k ≈ 1.5-2.5)
9. Loss Analysis
Major Loss Sources:
- Friction losses: Proportional to c²/2g
- Shock losses: At off-design conditions
- Leakage losses: Through clearances
- Disk friction: Proportional to ω³·r⁵
- Recirculation: At low flow rates
Total head loss coefficient:
k_total = k_friction + k_shock + k_incidence + k_diffusion
Design Rules of Thumb
General Guidelines
-
Specific Speed Range:
- Single-stage: Ns = 10-150
- Multi-stage for Ns < 20 (high head, low flow)
- Axial for Ns > 150 (low head, high flow)
-
Blade Angles:
- Inlet: β1 = 18-28° (typical)
- Outlet: β2 = 20-30° (backward-curved)
- Never exceed β2 > 40° (poor efficiency)
-
Velocities:
- Meridional: c_m = 2-5 m/s
- Outlet absolute: c2 = 10-25 m/s
- Inlet relative: w1 < 20 m/s (cavitation limit)
-
Dimensional Ratios:
- D2/D1 = 1.5-2.5 (radial pumps)
- b2/D2 = 0.02-0.08 (decreases with Ns)
- Blade thickness: t = 3-6 mm (depends on material and size)
-
Number of Blades:
- Radial pumps: Z = 5-7
- Mixed flow: Z = 5-8
- Axial flow: Z = 3-5
- More blades = higher head, lower efficiency
-
Clearances:
- Impeller shroud clearance: 0.2-0.5 mm (small pumps)
- Wear ring clearance: 0.3-0.8 mm
- Minimize to reduce leakage losses
Performance Guidelines
-
Efficiency:
- Small pumps (P < 20 kW): η = 60-75%
- Medium pumps (20-200 kW): η = 75-85%
- Large pumps (P > 200 kW): η = 85-92%
-
Operating Range:
- Recommended: 70-120% of design flow
- Maximum: 50-150% of design flow
- Avoid continuous operation below 40% (recirculation)
-
NPSH Safety Margin:
- NPSH_available > 1.3 × NPSH_required (minimum)
- NPSH_available > 2.0 × NPSH_required (recommended)
Material Selection
-
Impeller Materials:
- Cast iron: Standard water service
- Bronze: Seawater, corrosive fluids
- Stainless steel (316): Chemical service
- Duplex stainless: High corrosion + high strength
-
Surface Finish:
- Ra < 1.6 μm for hydraulic surfaces
- Ra < 3.2 μm for back shroud
- Polish for slurries (Ra < 0.8 μm)
Common Design Mistakes to Avoid
Critical Errors
-
Incorrect Specific Speed Application:
- ❌ Using total head instead of head per stage
- ❌ Mixing unit systems (US vs. European Ns)
- ✅ Always calculate Ns with consistent units
- ✅ Select pump type based on correct Ns range
-
Velocity Triangle Errors:
- ❌ Assuming c_u1 ≠ 0 without pre-rotation device
- ❌ Using u1 at hub instead of mean diameter
- ✅ Calculate velocities at correct radii
- ✅ Verify vector addition: c = u + w
-
Excessive Blade Angles:
- ❌ β2 > 35° causes instability and low efficiency
- ❌ β1 < 10° causes manufacturing difficulties
- ✅ Keep β2 = 20-30° for stable operation
- ✅ Ensure blade angles are manufacturable
-
Ignoring Slip:
- ❌ Using H_th without slip correction
- ❌ Neglecting finite blade number effects
- ✅ Apply slip factor: σ = 1 - π·sin(β2)/Z
- ✅ Actual head H = σ·H_th
-
Poor Suction Design:
- ❌ Insufficient NPSH margin
- ❌ Excessive inlet velocity (cavitation)
- ✅ Keep inlet velocity < 3-4 m/s
- ✅ NPSH_avail > 1.5 × NPSH_req minimum
-
Unrealistic Efficiency:
- ❌ Assuming η > 0.90 for small pumps
- ❌ Not accounting for scale effects
- ✅ Use correlations based on size and Ns
- ✅ Validate against similar pump data
Design Optimization Issues
-
Over-Designing:
- Using too many blades (increases friction)
- Excessive impeller diameter (higher cost, power)
- Too narrow outlet width (high velocity, losses)
-
Under-Designing:
- Too few blades (slip losses, uneven flow)
- Insufficient outlet width (cavitation)
- Inadequate structural analysis (fatigue failure)
-
Manufacturing Constraints:
- Blade angles too complex for casting
- Insufficient blade thickness for welding
- Tight tolerances without justification
-
System Mismatch:
- Selecting pump for single duty point
- Not considering system curve variation
- Ignoring start-up and shutdown conditions
Verification and Validation
Design Verification Checklist
- Specific speed within acceptable range for pump type
- Blade angles manufacturable (β1, β2 > 10°)
- Velocities within recommended limits
- NPSH available exceeds required by 30%+
- Efficiency estimate reasonable for pump size
- Slip factor applied to theoretical head
- Structural analysis for rotational stresses
- Leakage paths minimized with proper clearances
Performance Validation
-
Dimensional Analysis:
- Check Reynolds number: Re = ρ·u2·D2/μ > 10⁶
- Verify Mach number: Ma = u2/a < 0.3
-
Affinity Laws:
- Q₂/Q₁ = (N₂/N₁) · (D₂/D₁)³
- H₂/H₁ = (N₂/N₁)² · (D₂/D₁)²
- P₂/P₁ = (N₂/N₁)³ · (D₂/D₁)⁵
-
Comparison with Similar Pumps:
- Benchmark against published data
- Compare dimensional ratios
- Validate efficiency predictions
Advanced Topics
Multi-Stage Pumps
For high heads:
Number of stages = H_total / H_per_stage
Select H_per_stage for optimal Ns (40-80 for best efficiency)
Variable Speed Operation
Using affinity laws:
Q ∝ N
H ∝ N²
P ∝ N³
Cavitation Analysis
Thoma cavitation parameter:
σ = NPSH_req / H
Typical values:
- σ = 0.06-0.12 (radial pumps)
- σ = 0.15-0.30 (axial pumps)
Computational Fluid Dynamics (CFD)
Modern design uses CFD for:
- Detailed flow field analysis
- Loss prediction
- Cavitation prediction
- Performance optimization
However, preliminary design still follows classical theory presented here.
Summary
Centrifugal pump design is a systematic process combining:
- Dimensional analysis (specific speed)
- Euler turbine equation (energy transfer)
- Velocity triangles (kinematics)
- Empirical correlations (efficiency, losses)
Success requires balancing theoretical calculations with practical experience and validation against existing designs.
References
See reference.md for detailed derivations, correlations, and literature references.
示例提示词
帮我用欧拉方程和速度三角形设计一台比转速合适的离心泵叶轮。
所属插件
安装该插件会一并获得同领域的 36 个 Skill / MCP。
同插件的其他科研 Skill
- ANSYS Fluent CFD仿真自动化Automates ANSYS Fluent CFD setup, meshing, and batch runs via Python scripting, journal files, and the PyAnsys ecosystem. Use when a user wants to script or automate an ANSYS Fluent simulation.
- Cantera燃烧仿真Runs Cantera combustion simulations: flame temperature, ignition delay, laminar flame speed, PSR. Use for mechanism-based combustion analysis tasks.
- 离心泵气蚀风险评估Calculates NPSHa and NPSHr and assesses cavitation risk for centrifugal pumps, with prevention and detection guidance. Use when sizing suction piping or diagnosing pump cavitation.
- 气蚀评估物性数据库Looks up vapor pressure, NPSHr data, and correlations for cavitation risk assessment in pumps. Use when cavitation-analysis needs reference property or NPSHr data.
- COMSOL多物理场耦合仿真Sets up coupled fluid-structure interaction simulations in COMSOL Multiphysics, focused on pump vibration analysis. Use when a user wants to script or automate a COMSOL FSI model.
- CoolProp流体物性查询Queries thermodynamic and transport properties for 100+ pure and pseudo-pure fluids via the CoolProp library. Use when a calculation needs fluid density, viscosity, or enthalpy data.
- 工程计算环境初始化Sets up a Python session with engineering constants, Pint units, and plotting defaults. Use at the start of a calculation session.
- 流体计算数值错误校验Handles common numerical errors in fluid calculations, such as division by zero and out-of-range physical values, with validation checks. Use when fluid code fails or returns unphysical results.
- 流体力学分析工作流Guides a systematic fluid dynamics analysis from problem setup and domain definition through model selection to validation. Use when planning a CFD or analytical fluid mechanics study end to end.
- 经验公式流体物性速算Computes quick fluid property estimates (density, viscosity, vapor pressure) from empirical correlations without needing a database. Use for fast order-of-magnitude property checks.
- 管道流动与泵选型计算Computes pipe flow, pump sizing, friction factor, and compressible flow results with the fluids Python package. Use for quick, code-based fluid mechanics calculations.
- 工程工具与数据库清点Enumerates installed Python packages, databases, and simulation tools available in the current environment. Use at the start of a session to avoid recommending unavailable tools.
- 管路元件损失系数查询Looks up loss coefficients (K-values) and equivalent lengths for pipes, valves, and fittings in pump and piping systems. Use when computing system head loss.
- 流体与材料物性查询Looks up temperature-dependent fluid viscosities, densities, and other material properties for pump and heat-transfer calculations. Use when a calculation needs property data at a given temperature.
- 泵性能曲线绘制Creates professional engineering plots such as pump performance curves, CFD velocity contours, and publication-quality figures with matplotlib. Use when a result needs a plotted figure.
- NASA大气与航空流体数据Accesses atmospheric property profiles and standard-atmosphere models from NASA Earthdata for high-altitude and aerospace fluid analysis. Use when a task needs altitude-dependent atmospheric data.
- 管网图论建模Models hydraulic piping networks and multi-pump systems as graphs using NetworkX flow algorithms. Use for analyzing flow distribution across a branched or looped piping network.
- REFPROP高精度物性查询Queries high-accuracy thermodynamic and transport properties from the commercial NIST REFPROP database. Use when a calculation needs reference-quality fluid property data and REFPROP is licensed.
- 数值数组计算Performs numerical array operations with NumPy: velocity field processing, pump curve interpolation, linear systems, and matrix methods. Use for general numerical computation in engineering code.
- OpenFOAM仿真与后处理Runs and post-processes OpenFOAM CFD simulations with PyFoam, pyvista, and vtk for mesh setup, solver control, and visualization. Use for scripted OpenFOAM workflows outside ParaView.
- 泵性能曲线与相似定律Generates and interprets pump H-Q/efficiency/power/NPSH curves, applies affinity laws, and predicts off-design performance. Use for pump curve analysis.
- 工程单位换算与量纲分析Handles engineering units with automatic conversion and dimensional-consistency checking using the Pint library. Use whenever a calculation mixes units or needs unit safety.
- 容积式泵设计分析Designs and analyzes gear, piston, and screw positive-displacement pumps, including volumetric efficiency and slip. Use when the pump is positive-displacement rather than centrifugal.
- 泵效率优化Maximizes pump efficiency through hydraulic design changes and operational strategies such as trimming, VFD control, and system matching. Use when a pump is running inefficiently.
常见问题
离心泵设计计算能做什么?
Designs centrifugal pumps from first principles using Euler equations, velocity triangles, and specific speed. Use for impeller sizing or new centrifugal pump design。
如何安装离心泵设计计算?
在科搭 Codar 左侧点击「插件」,在「组件」页签搜索「离心泵设计计算」并安装;在 Claude Code 或 Codex 中可以发送本页的安装提示词,或下载 Skill 包后解压到 ~/.claude/skills 或 ~/.codex/skills。
离心泵设计计算需要哪些权限?
该科研 Skill没有声明额外权限;执行具体操作时仍由 Agent 按自身规则请求确认。
离心泵设计计算经过官方审核吗?
是。SpeedSkills 收录的每个版本都会记录内容摘要与权限声明,当前版本已通过安全审核。