科研 Skill
工程材料选型设计
materials-selection-design
Selects engineering materials via material indices and Ashby charts, ranking candidates by performance per cost or mass. Use when picking a material class for a design constraint.
SKILL.md
Materials Selection and Design
Purpose
Turn an engineering design requirement (a beam that must not fail under bending, a heat exchanger wall, a lightweight pressure vessel) into a short, ranked list of candidate materials, using the Ashby material-selection method: translate function, objective, and constraints into a material index, then screen a materials universe against that index on log-log property charts. This skill is the systematic bridge between "what does the part need to do" and "which material class should a downstream simulation or characterization skill investigate further" — it does not run DFT, MD, or mechanical tests itself.
When to Use This Skill
Activate when the request involves:
- Choosing between material classes or specific alloys/polymers/ceramics/composites for a part subject to a structural, thermal, or electrical constraint.
- "Minimize mass/cost for a given stiffness/strength," "select a material for X," "which material class should I simulate/test next."
- Building or reading an Ashby chart (e.g., Young's modulus vs. density, strength vs. density) and computing where a material index line falls on it.
- Comparing material indices across candidate classes to shortlist 3-5 options before committing to expensive DFT, MD, or experimental characterization.
Do not use this skill to perform the downstream physics: once a material class is
selected, hand off to computational-materials, finite-element-modeling,
mechanical-testing, or similar skills in this plugin to validate the choice.
Core Method: Function, Objective, Constraint, Free Variable
Every selection problem is decomposed into four elements before any chart is drawn:
- Function — what the component does (tie, beam, panel, shaft, pressure vessel, heat exchanger, electrical conductor, spring).
- Objective — what to minimize or maximize (mass, cost, volume, energy, or a combination such as cost per unit stiffness).
- Constraints — fixed requirements that must be satisfied (must support load F without failing, must not exceed deflection delta, must survive temperature T, must be electrically insulating, must be machinable).
- Free variables — what the designer can still choose (cross-sectional dimensions, material).
The key step is substituting the constraint equation into the objective equation to separate variables that depend on geometry from variables that depend only on material. The material-only part is the material index (sometimes called a material performance index), written M.
Deriving a Material Index (Worked Pattern)
For a light, stiff tie-rod of fixed length L under axial load F, with target deflection-free (fully stiff) behavior and free cross-section A:
- Objective: minimize mass, m = A * L * rho
- Constraint: stiffness S = F/delta = A * E / L (rearrange for A)
- Substitute: m = (S * L^2 / E) * rho = S * L^2 * (rho / E)
Mass is minimized by minimizing rho/E, i.e. by maximizing E/rho. The material index for this case is:
M = E / rho (stiffness-limited tie, minimize mass)
The same procedure for common cases:
| Component / Constraint | Objective | Material index M (maximize) |
|---|---|---|
| Tie, stiffness-limited | minimize mass | E / rho |
| Tie, strength-limited | minimize mass | sigma_y / rho |
| Beam, stiffness-limited (fixed section shape) | minimize mass | E^(1/2) / rho |
| Beam, strength-limited | minimize mass | sigma_y^(2/3) / rho |
| Panel, stiffness-limited (fixed width, free thickness) | minimize mass | E^(1/3) / rho |
| Column, buckling-limited | minimize mass | E^(1/2) / rho |
| Spring, store max energy per mass | minimize mass | sigma_y^2 / (E * rho) |
| Thermal insulation, steady state | minimize mass for fixed heat loss | 1 / (lambda) with rho via thickness tradeoff |
| Electrical conductor, fixed resistance | minimize mass | rho_density / sigma_electrical |
| Minimize material cost instead of mass | same as above | replace rho with rho * Cm (cost per mass) in the denominator |
Where E = Young's modulus, rho = density, sigma_y = yield strength, lambda = thermal conductivity, Cm = cost per unit mass. For beams and panels the index exponent depends on which dimension is free versus fixed — re-derive it if the geometry differs from "fixed length, free cross-section."
Reading and Building Ashby Charts
An Ashby chart plots one material property against another on log-log axes (e.g., Young's modulus E vs. density rho), with each material class (steels, Al alloys, Ti alloys, engineering polymers, technical ceramics, composites, foams, woods, elastomers) shown as a labeled bubble or envelope spanning its typical property range.
- Plot the two properties that appear in the candidate material indices.
- For an index of the form M = E^n / rho, a line of the form
log(E) = n * log(rho) + n * log(M)is a selection line of slope n on the E-rho chart. Materials above/left of the line (depending on which direction is better) outperform those below it for that index. - Slide the selection line across the chart; materials it touches last, in the direction of improving performance, are the best performers for that index, independent of the absolute scale of the design.
- Apply constraint boxes second: eliminate materials that fail a hard requirement (max service temperature, corrosion environment, electrical insulation, recyclability) before ranking by the index. A material with the best index that fails a hard constraint is not a candidate.
Reference material property ranges (order-of-magnitude, for sanity-checking a screen, not for final design) by class:
| Class | E (GPa) | rho (Mg/m^3) | sigma_y (MPa) | Typical max service T (C) |
|---|---|---|---|---|
| Steels | 190-210 | 7.5-8.0 | 200-2000 | 400-650 |
| Al alloys | 68-82 | 2.6-2.9 | 50-600 | 150-250 |
| Ti alloys | 80-130 | 4.3-4.8 | 300-1200 | 300-550 |
| Ni superalloys | 190-220 | 8.0-9.0 | 600-1200 | 900-1100 |
| Engineering polymers | 1-4 | 0.9-1.5 | 20-100 | 60-150 |
| Technical ceramics (Al2O3, SiC) | 300-450 | 3.0-3.9 | n/a (brittle; use fracture strength) | 1000-1600 |
| CFRP (unidirectional) | 70-200 (fiber direction) | 1.5-1.6 | 600-1800 (tensile, fiber direction) | 120-180 (matrix-limited) |
| Metal/polymer foams | 0.001-1 | 0.02-0.6 | 0.1-20 | class-dependent |
These are illustrative midpoints; always pull current numbers from a materials
property database (see materials-databases, materials-databases-access) or a
vetted handbook (ASM Handbooks, MatWeb, Granta/CES Selector data) before finalizing
a selection — this skill's tables are for first-pass screening only.
Multi-Objective and Penalty-Function Ranking
When mass and cost (or mass and another property) must be minimized together and no single index dominates:
- Normalize each candidate's performance on every objective to a 0-1 scale relative to the best and worst candidate in the shortlist.
- Combine with a weighted penalty function
Z = sum(w_i * normalized_value_i), choosing weights w_i by stakeholder priority (this step is inherently subjective — document the weights used). - Alternatively, compute a trade-off (Pareto) surface in the two objectives and
present the non-dominated set rather than collapsing to one weighted score; this
avoids hiding the trade-off from the decision-maker. For automated multi-objective
search once a numeric model exists, see
bayesian-optimization.
Shape Factors (When Section Shape Is a Free Variable)
If the cross-sectional shape (I-beam, tube, box) is also a design variable rather
than fixed, a shape factor phi multiplies the material index to capture how much
stiffness or strength a given material can gain from efficient shaping (e.g., a
thin-walled tube is far stiffer per unit mass than a solid rod of the same
material). Shape factors are material-class dependent (metals can be extruded or
machined into efficient open/closed sections; ceramics are limited to simple
convex shapes to avoid stress concentrations in manufacturing). When shape is free,
compare M * phi across classes rather than M alone, and verify the assumed shape
is actually manufacturable in that material class.
Prerequisites
- The design requirement must already be reduced to a function, an objective, and
at least one constraint; this skill does not perform structural analysis to derive
loads or deflection limits (use
finite-element-modelingorfem-multiphysicsfor that upstream step if loads are not already known). - Reasonably current material property data for the candidate universe — this skill's property table is illustrative only and must not be used for a final, safety-relevant decision.
Limitations
- Ashby selection identifies promising material classes/indices, not a specific
qualified alloy, heat treatment, or supplier grade; a final choice still requires
specification-level data (e.g., an aerospace material spec sheet) and, for
safety-critical parts, testing per
mechanical-testingorfatigue-analysis-workflow. Fully ceramics and other brittle materials have no single "strength" — treat catalogsigma_yfor ceramics as flexural/fracture strength to be revisited with thefracture-mechanics-workflowandmaterials-stats(Weibull) skills. - Material indices above assume elastic, linear, isotropic behavior; anisotropic materials (composites, single-crystal or textured metals) need directional property values, not the single scalar E/sigma_y shown in generic handbook ranges.
- Cost data is volatile (commodity price swings, region-specific supply chains) and is not tracked by this skill; treat any embedded cost figures as placeholders.
- Does not account for manufacturability, joining, or supply-chain constraints beyond simple constraint-box screening; these frequently eliminate an index-optimal material in practice.
Quality Checks
- The derived material index matches the stated objective and constraint (re-derive by substitution rather than pattern-matching to the table when the geometry differs from the standard cases above).
- Every shortlisted material satisfies all hard constraints (temperature, environment, electrical/magnetic behavior), not just the ranked index.
- Property values used for the final ranking are sourced from a specific database or handbook entry (with units and temperature noted), not from this skill's illustrative table.
- For brittle or anisotropic candidates, flag explicitly that scalar yield-strength comparisons are not directly meaningful and that downstream validation is needed.
示例提示词
帮我用Ashby材料选型法为这个承重结构件筛选出几种候选材料。
所属插件
安装该插件会一并获得同领域的 42 个 Skill / MCP。
同插件的其他科研 Skill
- 贝叶斯优化材料发现Covers Bayesian optimization for materials and chemistry design: surrogate models, acquisition functions, batch/constrained BO. Use when planning sample-efficient experiments or simulations.
- CALPHAD热力学计算工作流Covers CALPHAD computational thermodynamics: database selection, equilibrium/metastable calculations, binary/ternary phase diagrams. Use when predicting phase stability or solidification paths.
- 材料第一性原理与分子动力学模拟Routes first-principles and classical materials simulation (DFT, MD, ML potentials) to the right specialized workflow. Use as an entry point for any simulation-based materials task.
- 蠕变力学建模与验证Selects, calibrates, and validates creep deformation and rupture models under sustained thermomechanical load, covering rate prediction. Use when assessing long-term high-temperature components.
- 晶体塑性有限元建模Covers crystal plasticity and CPFE modeling of metals: slip systems for FCC/BCC/HCP, Schmid factors. Use when simulating texture- and orientation-dependent plastic deformation.
- 衍射结构表征Covers diffraction-based structure characterization (XRD, neutron, SAED): space group determination, Rietveld refinement, phase identification. Use for any diffraction-pattern analysis technique.
- EBSD织构分析Analyzes EBSD orientation maps for grain size, misorientation, phase, and texture, with pole figures and twin-boundary identification. Use for electron backscatter diffraction workflows.
- 电化学性能测试分析Covers electrochemical characterization: cyclic voltammetry, battery cycling analysis, EIS. Use for electrochemistry-specific data analysis distinct from general materials characterization.
- 金属疲劳寿命评估Builds, calibrates, and validates fatigue assessments for metals and components: stress-life, strain-life, multiaxial critical-plane. Use when predicting fatigue life or crack growth.
- 多物理场有限元建模Covers finite element modeling for coupled materials, mechanics, and transport problems: weak-form construction, boundary conditions, mesh choice. Use for multiphysics FEM simulations.
- 连续尺度有限元力学建模Covers continuum-scale mechanical, thermal, and multiphysics simulation with Abaqus/COMSOL conventions, mesh generation. Use for macroscale FEM consuming measured or computed material properties.
- 断裂力学评估与建模Selects, constructs, and validates fracture-mechanics assessments: LEFM checks, elastic-plastic fracture mechanics. Use when assessing cracked materials or components.
- 高斯过程材料回归建模Covers Gaussian process regression for materials and chemistry datasets: descriptor selection, kernel design. Use when a probabilistic surrogate model with uncertainty is needed.
- 自驱动实验室闭环材料发现Covers combinatorial synthesis, robotic experimentation. Use for autonomous or robotics-driven experimental campaigns, a less standardized domain.
- 材料数据库可复现访问Covers reproducible API access to materials databases (Materials Project, AFLOW, OQMD, NOMAD, COD, ICSD-style sources): authentication. Use when programmatically querying these databases.
- 材料数据库跨库查询Covers querying public materials databases beyond Materials Project: AFLOW, OQMD, NOMAD, JARVIS. Use when pulling or comparing data from these live, API-integrated resources.
- 材料数据标准与互操作Covers data interoperability standards for materials science: CIF crystal files, the OPTIMADE query API. Use when structuring or exchanging materials data between tools.
- 材料结构特征化Covers converting structures, compositions, and trajectories into ML feature vectors: Magpie-style elemental statistics. Use when building inputs for materials ML models.
- 材料科学图表绘制规范Covers publication-quality figure conventions for materials science plots: phase diagrams, pole figures, stress-strain curves. Use when the deliverable is a figure, not just an analysis result.
- 材料信息学性质预测Covers ML for materials property prediction and generative design: descriptor-based models, crystal GNNs (CGCNN/MEGNet-class). Use for materials informatics distinct from interatomic potentials.
- 材料生命周期评估Covers life-cycle assessment for materials and manufacturing routes: goal/scope definition, functional units, inventory construction. Use for environmental-impact studies of materials.
- 材料科学文献检索Covers formulating literature search queries for materials science questions and synthesizing/citing results responsibly. Requires a web search tool; it cannot substitute for one.
- 材料统计方法与实验设计Covers statistics shared across materials characterization and simulation: design of experiments. Use for cross-cutting statistical treatment of materials data.
- 材料结构与成分核心分析Covers core structure and composition analysis: reading/writing crystal structures, composition handling, symmetry analysis, phase diagrams. Use as a general-purpose structure-analysis toolkit.
常见问题
工程材料选型设计能做什么?
Selects engineering materials via material indices and Ashby charts, ranking candidates by performance per cost or mass. Use when picking a material class for a design constraint。
如何安装工程材料选型设计?
在科搭 Codar 左侧点击「插件」,在「组件」页签搜索「工程材料选型设计」并安装;在 Claude Code 或 Codex 中可以发送本页的安装提示词,或下载 Skill 包后解压到 ~/.claude/skills 或 ~/.codex/skills。
工程材料选型设计需要哪些权限?
该科研 Skill没有声明额外权限;执行具体操作时仍由 Agent 按自身规则请求确认。
工程材料选型设计经过官方审核吗?
是。SpeedSkills 收录的每个版本都会记录内容摘要与权限声明,当前版本已通过安全审核。