科研 Skill
EBSD织构分析
ebsd-texture-analysis
Analyzes EBSD orientation maps for grain size, misorientation, phase, and texture, with pole figures and twin-boundary identification. Use for electron backscatter diffraction workflows.
SKILL.md
EBSD and Crystallographic Texture Analysis
Purpose
Process electron backscatter diffraction (EBSD) orientation maps into
quantitative microstructure and texture descriptors: grain size and shape
distributions, grain-boundary character (low-angle vs. high-angle, special
coincidence-site-lattice boundaries, twin boundaries), phase maps, and bulk
crystallographic texture (pole figures, inverse pole figures, orientation
distribution functions). It complements microscopy (which covers SEM/TEM/AFM
imaging generically) with the orientation-specific analysis that EBSD uniquely
provides, and complements diffraction (XRD/neutron/SAED phase and structure
identification) with spatially resolved, per-grain crystallographic information.
When to Use This Skill
Activate when the request involves:
- Raw or processed EBSD data (
.ang,.ctf,.osc,.h5orientation maps), Kikuchi pattern indexing results, or orientation-map images. - "Grain size from EBSD," "texture/ODF," "pole figure," "inverse pole figure (IPF) map," "misorientation angle/axis," "twin boundary fraction," "texture index," "Taylor factor," "recrystallization fraction from EBSD."
- Deciding whether an observed deformation or annealing texture matches an expected fiber/component texture (e.g., rolling texture in FCC/BCC metals).
- Providing experimentally measured texture or grain statistics as input to
crystal-plasticity-workflow(initial orientation distribution) ormaterials-figures(pole-figure plotting conventions).
Not for indexing raw Kikuchi patterns from scratch (that step happens in vendor/open-source acquisition software such as OIM Analysis, AZtecCrystal, or MTEX/EBSD-indexing pipelines before this skill's analysis begins) and not for transmission-EBSD (t-EBSD) hardware setup.
Core Data and Coordinate Conventions
An indexed EBSD scan assigns each pixel a crystallographic orientation (as a rotation, usually stored as Euler angles in the Bunge convention (phi1, Phi, phi2) or as a quaternion/rotation matrix), a phase ID, and indexing quality metrics (confidence index CI, image quality IQ, fit/MAD). Before any texture or grain analysis:
- Clean the data. Remove or flag points below a confidence-index threshold (commonly CI < 0.1, but this is instrument- and sample-dependent — check the CI histogram rather than applying a fixed cutoff blindly) and known indexing artifacts (pseudosymmetry mis-indexing, zero-solution points).
- Confirm phase assignment is correct where multiple phases are present; pseudosymmetric phases (e.g., austenite/ferrite in some steels, or phases with near-identical lattice parameters) are a common source of EBSD mis-indexing that downstream texture analysis will silently propagate.
- Check the reference frame. Sample coordinate axes (RD/TD/ND — rolling, transverse, normal direction for rolled sheet, or equivalent for the actual process) must be correctly assigned before any pole figure or fiber-texture statement is meaningful; a software default frame that does not match the physical sample mounting produces a texture result that is internally consistent but physically mislabeled.
Grain Reconstruction and Grain Size
Grains are reconstructed from the pixel orientation map by grouping neighboring pixels whose misorientation is below a grain-boundary threshold (commonly 2-5 deg for the low-angle/sub-grain threshold and 10-15 deg for the conventional high-angle grain boundary definition — state which threshold was used, since grain size statistics are sensitive to it).
- Report grain size via the equivalent circular diameter (ECD) from grain area, and give the distribution (not just a mean) — grain size in most metals is approximately log-normal, so a simple arithmetic mean understates the role of a long large-grain tail.
- Exclude or flag edge-truncated grains (grains cut by the scan boundary) before computing size statistics, or correct for the truncation bias explicitly.
- Distinguish area-weighted mean grain size from number-weighted mean — they differ substantially for broad distributions and are not interchangeable when comparing to a specification (e.g., ASTM E112 grain size number) that defines one specific convention.
Misorientation and Grain-Boundary Character
- Misorientation between two orientations is the minimum rotation angle relating them, accounting for crystal symmetry (the disorientation, i.e. the smallest equivalent angle among all symmetry-equivalent representations). Compute it via quaternion or rotation-matrix misorientation, not by naive Euler angle subtraction, which is not rotationally meaningful.
- Low-angle boundaries (LAGBs, <~15 deg) typically represent sub-grain or dislocation-cell structure; high-angle boundaries (HAGBs) are conventional grain boundaries.
- Coincidence-site-lattice (CSL) boundaries, identified via Brandon's criterion (allowed deviation from the exact CSL misorientation scales as 15 deg / Sigma^0.5), flag special boundaries such as Sigma3 annealing twins in FCC metals — report twin (Sigma3) boundary length/area fraction separately from the general HAGB population when twinning is mechanistically relevant (e.g., annealing-twin density in low-stacking-fault-energy FCC alloys).
Texture: Pole Figures, IPF Maps, and the ODF
- IPF (inverse pole figure) maps color each pixel by which crystallographic direction is parallel to a chosen sample direction (commonly the sample normal or loading direction); they show spatial texture heterogeneity but are not a quantitative bulk texture measure by themselves.
- Pole figures project the density of a chosen crystallographic plane normal (e.g., {111}, {200} for FCC) onto a sample-direction stereographic projection, summarizing bulk texture as measured intensity relative to a random (texture-free) distribution (multiples of random density, MRD/MUD).
- Orientation distribution function (ODF), typically computed via harmonic series expansion or discrete binning over Euler space, is the complete texture descriptor from which any pole figure can be recovered; report ODF results in a stated Euler-angle convention and symmetry-reduced fundamental zone appropriate to the crystal and sample symmetry.
- Texture index (J-index, the integral of ODF^2) gives a single scalar "texture sharpness" summary — useful for tracking texture evolution across a processing series, not for distinguishing texture components from each other.
- Compare measured fiber/component textures (e.g., alpha-fiber, gamma-fiber in BCC rolled steel; Cube, Goss, Brass, Copper, S components in FCC metals) against standard idealized texture-component tables rather than inventing ad hoc component names.
Recommended Tools
- MTEX (MATLAB toolbox) — open-source, the most complete free option for
pole figures, ODF computation, grain reconstruction, and misorientation
analysis directly from
.ctf/.angfiles. - orix / defdap (Python) — open-source alternatives for orientation data handling, grain segmentation, and plotting within a Python pipeline.
- Vendor software (OIM Analysis, AZtecCrystal, Esprit) for initial indexing and
basic maps; export to
.ang/.ctf/.h5for reproducible, scriptable reanalysis in MTEX/orix rather than relying solely on vendor GUI output.
Prerequisites
- Already-indexed EBSD data (orientation + phase + quality-metric per pixel) in
a standard export format (
.ang,.ctf,.h5/.h5oina); this skill does not perform Kikuchi pattern indexing. - A stated, physically verified sample coordinate frame (RD/TD/ND or equivalent) and a stated confidence-index/quality cleaning threshold.
- For CSL/twin-boundary analysis, correct crystal symmetry and lattice parameter for each phase present.
Limitations
- EBSD samples a 2D surface section through a 3D microstructure; grain size and shape from a single section are stereologically biased (sections rarely pass through a grain's true center) — true 3D grain size requires serial sectioning, 3D-EBSD, or a stereological correction, not a single 2D map.
- Step size and indexing resolution set a hard lower bound on resolvable grain size and sub-structure; sub-grain or dislocation-cell features finer than a few step sizes are not reliably captured.
- Pseudosymmetry, surface damage (from poor polishing), and low pattern quality near grain boundaries bias both grain reconstruction and misorientation statistics near boundaries specifically — do not over-interpret boundary-adjacent misorientation gradients without checking local pattern quality.
- Texture results are only as representative as the scanned area is of the bulk material; for strongly textured or coarse-grained material, confirm the scan covers enough grains (typically hundreds to thousands) for a statistically meaningful ODF before reporting bulk texture conclusions.
Quality Checks
- Confidence-index/quality cleaning threshold and grain-boundary misorientation threshold are both stated explicitly alongside any grain size or texture result.
- Grain size is reported as a distribution (with area- vs. number-weighting specified), not a single unqualified mean.
- The sample coordinate frame used for pole figures/IPF maps is confirmed to match the physical sample mounting direction.
- CSL/twin fractions use Brandon's criterion (or another explicitly stated tolerance) rather than an exact-match-only definition.
- Texture conclusions state the number of grains/orientations sampled, so a reader can judge statistical adequacy.
示例提示词
帮我分析这组EBSD取向数据的晶粒尺寸、晶界特征和宏观织构。
所属插件
安装该插件会一并获得同领域的 42 个 Skill / MCP。
同插件的其他科研 Skill
- 贝叶斯优化材料发现Covers Bayesian optimization for materials and chemistry design: surrogate models, acquisition functions, batch/constrained BO. Use when planning sample-efficient experiments or simulations.
- CALPHAD热力学计算工作流Covers CALPHAD computational thermodynamics: database selection, equilibrium/metastable calculations, binary/ternary phase diagrams. Use when predicting phase stability or solidification paths.
- 材料第一性原理与分子动力学模拟Routes first-principles and classical materials simulation (DFT, MD, ML potentials) to the right specialized workflow. Use as an entry point for any simulation-based materials task.
- 蠕变力学建模与验证Selects, calibrates, and validates creep deformation and rupture models under sustained thermomechanical load, covering rate prediction. Use when assessing long-term high-temperature components.
- 晶体塑性有限元建模Covers crystal plasticity and CPFE modeling of metals: slip systems for FCC/BCC/HCP, Schmid factors. Use when simulating texture- and orientation-dependent plastic deformation.
- 衍射结构表征Covers diffraction-based structure characterization (XRD, neutron, SAED): space group determination, Rietveld refinement, phase identification. Use for any diffraction-pattern analysis technique.
- 电化学性能测试分析Covers electrochemical characterization: cyclic voltammetry, battery cycling analysis, EIS. Use for electrochemistry-specific data analysis distinct from general materials characterization.
- 金属疲劳寿命评估Builds, calibrates, and validates fatigue assessments for metals and components: stress-life, strain-life, multiaxial critical-plane. Use when predicting fatigue life or crack growth.
- 多物理场有限元建模Covers finite element modeling for coupled materials, mechanics, and transport problems: weak-form construction, boundary conditions, mesh choice. Use for multiphysics FEM simulations.
- 连续尺度有限元力学建模Covers continuum-scale mechanical, thermal, and multiphysics simulation with Abaqus/COMSOL conventions, mesh generation. Use for macroscale FEM consuming measured or computed material properties.
- 断裂力学评估与建模Selects, constructs, and validates fracture-mechanics assessments: LEFM checks, elastic-plastic fracture mechanics. Use when assessing cracked materials or components.
- 高斯过程材料回归建模Covers Gaussian process regression for materials and chemistry datasets: descriptor selection, kernel design. Use when a probabilistic surrogate model with uncertainty is needed.
- 自驱动实验室闭环材料发现Covers combinatorial synthesis, robotic experimentation. Use for autonomous or robotics-driven experimental campaigns, a less standardized domain.
- 材料数据库可复现访问Covers reproducible API access to materials databases (Materials Project, AFLOW, OQMD, NOMAD, COD, ICSD-style sources): authentication. Use when programmatically querying these databases.
- 材料数据库跨库查询Covers querying public materials databases beyond Materials Project: AFLOW, OQMD, NOMAD, JARVIS. Use when pulling or comparing data from these live, API-integrated resources.
- 材料数据标准与互操作Covers data interoperability standards for materials science: CIF crystal files, the OPTIMADE query API. Use when structuring or exchanging materials data between tools.
- 材料结构特征化Covers converting structures, compositions, and trajectories into ML feature vectors: Magpie-style elemental statistics. Use when building inputs for materials ML models.
- 材料科学图表绘制规范Covers publication-quality figure conventions for materials science plots: phase diagrams, pole figures, stress-strain curves. Use when the deliverable is a figure, not just an analysis result.
- 材料信息学性质预测Covers ML for materials property prediction and generative design: descriptor-based models, crystal GNNs (CGCNN/MEGNet-class). Use for materials informatics distinct from interatomic potentials.
- 材料生命周期评估Covers life-cycle assessment for materials and manufacturing routes: goal/scope definition, functional units, inventory construction. Use for environmental-impact studies of materials.
- 材料科学文献检索Covers formulating literature search queries for materials science questions and synthesizing/citing results responsibly. Requires a web search tool; it cannot substitute for one.
- 工程材料选型设计Selects engineering materials via material indices and Ashby charts, ranking candidates by performance per cost or mass. Use when picking a material class for a design constraint.
- 材料统计方法与实验设计Covers statistics shared across materials characterization and simulation: design of experiments. Use for cross-cutting statistical treatment of materials data.
- 材料结构与成分核心分析Covers core structure and composition analysis: reading/writing crystal structures, composition handling, symmetry analysis, phase diagrams. Use as a general-purpose structure-analysis toolkit.
常见问题
EBSD织构分析能做什么?
Analyzes EBSD orientation maps for grain size, misorientation, phase, and texture, with pole figures and twin-boundary identification. Use for electron backscatter diffraction workflows。
如何安装EBSD织构分析?
在科搭 Codar 左侧点击「插件」,在「组件」页签搜索「EBSD织构分析」并安装;在 Claude Code 或 Codex 中可以发送本页的安装提示词,或下载 Skill 包后解压到 ~/.claude/skills 或 ~/.codex/skills。
EBSD织构分析需要哪些权限?
该科研 Skill没有声明额外权限;执行具体操作时仍由 Agent 按自身规则请求确认。
EBSD织构分析经过官方审核吗?
是。SpeedSkills 收录的每个版本都会记录内容摘要与权限声明,当前版本已通过安全审核。